AudioRoundTable.com: Craftsmen » Table saw recommendations?

Home » Audio » Craftsmen » Table saw recommendations?

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: Table saw recommendations? [message #28991 is a reply to message #28990]

Mon, 29 March 2004 07:34

Dean Kukral
Messages: 177
Registered: May 2009

Master

When I have a project, I usually have the store cut the 4x8 into slightly oversize pieces and then I neatly trim them when I get home. They do it for free or for a nominal fee.

I doubt that you can do much for under $500, but I have not looked.

I suggest that you get one of those fences for portable power hand saws. You clamp the fence to the 4x8 and run the saw along side of the fence. They are not too expensive.

Report message to a moderator

[Message index]

		Table saw recommendations? By: crazychile on Mon, 29 March 2004 06:47
		Re: Table saw recommendations? By: Dean Kukral on Mon, 29 March 2004 07:34
		follow-up By: Dean Kukral on Mon, 29 March 2004 07:50
		Re: follow-up By: crazychile on Tue, 30 March 2004 06:19
		Re: follow-up By: Bill Fitzmaurice on Tue, 30 March 2004 06:56
		Re: follow-up By: Dean Kukral on Tue, 30 March 2004 18:50
		Re: follow-up By: Bill Fitzmaurice on Wed, 31 March 2004 06:11
		Re: follow-up By: Dean Kukral on Wed, 31 March 2004 06:33
		Re: follow-up By: Bill Fitzmaurice on Wed, 31 March 2004 08:38
		Re: More so with MDF By: BillEpstein on Wed, 31 March 2004 17:00
		Wait a minute By: Dean Kukral on Wed, 31 March 2004 06:49
		Re: Wait a minute By: Bill Martinelli on Fri, 02 April 2004 21:35
		Re: follow-up By: crazychile on Wed, 31 March 2004 09:40
		Re: follow-up By: Bill Fitzmaurice on Wed, 31 March 2004 09:56
		Re: follow-up By: crazychile on Fri, 02 April 2004 06:17
		Re: Table saw recommendations? By: Ryder on Mon, 29 March 2004 07:36
		Re: Table saw recommendations? By: elektratig on Mon, 29 March 2004 16:15
		Re: Table saw recommendations? By: wunhuanglo on Mon, 29 March 2004 16:45
		Re: All this is good stuff and.......... By: BillEpstein on Tue, 30 March 2004 20:32
		Re: BT3100 By: wunhuanglo on Wed, 31 March 2004 05:06
		Need more capacity? Make a bigger jig. By: Bill Fitzmaurice on Wed, 31 March 2004 06:06
		Re: REply to bigger capacity and sucky Ryobi By: BillEpstein on Wed, 31 March 2004 16:49
		Re: sucky Ryobi - Sorry, I disagree By: wunhuanglo on Wed, 31 March 2004 18:01
		Re: More space than saw By: Bill Martinelli on Wed, 31 March 2004 22:10

Previous Topic:	Tube PreAmp - Done! (almost)
Next Topic:	For Beginners

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Fri May 10 00:01:32 CDT 2024