AudioRoundTable.com: Pi Speakers » 1pi or 2pi for surrounds?

Home » Sponsored » Pi Speakers » 1pi or 2pi for surrounds?

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: 1pi or 2pi for surrounds? [message #69251 is a reply to message #69250]

Tue, 30 August 2011 22:40

Wayne Parham
Messages: 18678
Registered: January 2001

Illuminati (33rd Degree)

Answers by numbers:

1. Use #6 pan head screws to attach the drivers to the baffle. You can get them at any hardware store, like Lowes, Home Depot or Sutherlands and even some department stores like Target or Walmart. If you can't find them with a black finish, you can paint the heads black with enamel and a small paint brush, like what you might use to paint a model.

2. Cut a rectangular hole 2-1/8" x 2-7/8" for the connector panel. We put them on the center of the back panel, 3" from the bottom.

3. The port is 2-1/2" diameter. I remember including the tube you should use, so look for a cardboard tube in the box. It's about 9" long. Cut two 3-1/2" long tubes from this with a table saw and glue them onto the baffle.

Report message to a moderator

[Message index]

		1pi or 2pi for surrounds? By: smokarz on Mon, 08 August 2011 08:52
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Mon, 08 August 2011 11:34
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 08 August 2011 11:49
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Mon, 08 August 2011 14:18
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 08 August 2011 14:46
		Re: 1pi or 2pi for surrounds? By: justphil on Tue, 09 August 2011 21:40
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 10 August 2011 07:52
		Re: 1pi or 2pi for surrounds? By: justphil on Wed, 10 August 2011 08:12
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 10 August 2011 09:59
		Re: 1pi or 2pi for surrounds? By: justphil on Wed, 10 August 2011 18:39
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 16 August 2011 12:32
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 16 August 2011 14:52
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 22 August 2011 10:02
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Mon, 22 August 2011 10:15
		Re: 1pi or 2pi for surrounds? By: smokarz on Fri, 26 August 2011 12:16
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Fri, 26 August 2011 12:40
		Re: 1pi or 2pi for surrounds? By: smokarz on Fri, 26 August 2011 12:46
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Fri, 26 August 2011 13:29
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 27 August 2011 08:26
		Re: 1pi or 2pi for surrounds? By: justphil on Sat, 27 August 2011 08:48
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Sat, 27 August 2011 09:32
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 27 August 2011 09:28
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 27 August 2011 09:36
		Re: 1pi or 2pi for surrounds? By: justphil on Sat, 27 August 2011 09:53
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 27 August 2011 10:27
		Re: 1pi or 2pi for surrounds? By: justphil on Sat, 27 August 2011 10:55
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 30 August 2011 21:55
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 30 August 2011 22:40
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 31 August 2011 08:54
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Wed, 31 August 2011 10:52
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 31 August 2011 12:20
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 06 September 2011 09:05
		Re: 1pi or 2pi for surrounds? By: justphil on Tue, 06 September 2011 09:24
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 06 September 2011 10:20
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 06 September 2011 12:50
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 06 September 2011 15:46
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 06 September 2011 20:24
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 06 September 2011 21:42
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 08 September 2011 10:10
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Thu, 08 September 2011 11:37
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 08 September 2011 15:06
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 10 September 2011 11:39
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Sat, 10 September 2011 16:32
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 12 September 2011 21:57
		Re: 1pi or 2pi for surrounds? By: jshupe on Wed, 08 January 2014 21:21
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 12 September 2011 21:58
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 12 September 2011 22:01
		Re: 1pi or 2pi for surrounds? By: justphil on Tue, 13 September 2011 09:36
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 13 September 2011 09:57
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 13 September 2011 10:29
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 13 September 2011 10:59
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 13 September 2011 14:15
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 13 September 2011 21:10
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 14 September 2011 21:08
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 14 September 2011 21:17
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Wed, 14 September 2011 22:10
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 15 September 2011 07:39
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Thu, 15 September 2011 07:49
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 15 September 2011 08:14
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Thu, 15 September 2011 10:25
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 15 September 2011 11:32
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Thu, 15 September 2011 12:35
		Helmholtz frequency of each model By: Wayne Parham on Fri, 16 September 2011 09:41
		Re: 1pi or 2pi for surrounds? By: smokarz on Fri, 16 September 2011 18:16
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Fri, 16 September 2011 19:30
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 17 September 2011 08:45
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Sat, 17 September 2011 09:00
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 17 September 2011 09:16
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Sat, 17 September 2011 10:45

Previous Topic:	Flanking subs and phase
Next Topic:	Pi 3 or 4?

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Thu Apr 25 20:05:10 CDT 2024