| |
71 Search Results Found |
| 1 |
Forum: Speaker «»
Posted on: Sun, 23 April 2006 20:34 «»
By: Crazy Dave
Re: Fostex SP11 MK II speakers
Your thoughts were similar to mine. The M&K is a powered sub with an active crossover. I do have a Dynaco ST-35 amp that might work well with it, as well as some good sand amps. I'm a vintage collector. It's too bad that nobody seems to know about the...
|
| 2 |
Forum: Pi Speakers «»
Posted on: Wed, 03 August 2005 14:58 «»
By: GarMan
Re: Suggestions for Active crossover for Theater 4 pi (long)
Chris, if I had a sub as nice as yours, I'd brag too.I'd only use the high-pass filter in a plate amp as a last resort. I think it's much better to use the natural rolloff of the main speakers and adjust the low-pass freq on the plate amp accordingly to ...
|
| 3 |
Forum: Pi Speakers «»
Posted on: Wed, 03 August 2005 14:13 «»
By: Chris R
Re: Suggestions for Active crossover for Theater 4 pi (long)
I don't have the particular setup you have, but I built a sub withone of the plate amps from Parts Express. Its the 250W, no remoteone. Its driven from the HT receiver sub out, so no external XO.The plate amp does have line level stereo in/out, so you c...
|
| 4 |
Forum: Pi Speakers «»
Posted on: Wed, 03 August 2005 11:34 «»
By: GarMan
Re: Suggestions for Active crossover for Theater 4 pi (long)
Frank,If you're using an active XO to divide the signal between your Theatre-4 and sub, there's no need for a passive XO in your sub.I re-read your original post again and you mentioned "active-sub" a few times. An "active-sub" usually has a plate amp (a...
|
| 5 |
Forum: Pi Speakers «»
Posted on: Wed, 03 August 2005 07:40 «»
By: GarMan
Re: Suggestions for Active crossover for Theater 4 pi (long)
Hey Frank,Good to see you completed the Theatre-4 and you're enjoying it. They don't go all the way down to shake your walls, but low enough for most music.I'm assuming what you want to do is keep the passive crossover in your Theatre-4 and use a 2-way a...
|
| 6 |
Forum: Pi Speakers «»
Posted on: Wed, 03 August 2005 06:40 «»
By: Frank Mena
Suggestions for Active crossover for Theater 4 pi (long)
Right now I have my Foreplay II & Paramours (with iron upgrade) with Theater 4 pi's and this system really kick's serious butt. Try as I might, my room dimensions/characteristic's won't let me get that bit of extra bass I would like to fill out the botto...
|
| 7 |
Forum: Speaker «»
Posted on: Fri, 29 July 2005 08:35 «»
By: eric j.
Line Array woofer system
I was in discussion recenty with a friend about shifting my sub woofer system on the 2 way array that I'm building, to a full 3 way array with a line source woofer array too.To keep the cost down I would use $11.25 Goldwood 7 inch poly woofers(fs=35), an...
|
| 8 |
Forum: Speaker «»
Posted on: Tue, 26 July 2005 23:53 «»
By: akhilesh
Re: Why won't a single driver speaker do metal?
Bob Brines wrote:"It won't work for the SET crowd because the cross over has to be done either digitally, which kind of takes the shine off of vinyl, or has to be done actively at the pre-amp level which normally means some OP amps."Actually, I use the Xo...
|
| 9 |
Forum: Speaker «»
Posted on: Mon, 25 April 2005 08:37 «»
By: GarMan
Tangbands had me at Hello
Okay. I'm sold! These little Tangbands are amazing! I bought a five pack of them with the intent of using them for computer speakers. They arrived Friday, dropped them into the 0.1 ft^3 ELF cabinets I built, and they sang right from the start. Very e...
|
| 10 |
Forum: Speaker «»
Posted on: Sun, 03 April 2005 18:06 «»
By: Jim Griffin
Re: MacIntosh XRT 29 Comments
Well, if you read what I said about the Mac design you should realize that 3000 Hz is too high to cross with this design unless you use smaller than 4" diameter drivers spaced really close together. You need to be shooting for a crossover in the low 2000...
|
Posting Rules
Members
Search
Help
Register
Login
Get a T-Shirt!
