Home » Sponsored » Pi Speakers » 4pi: B&C DE 250 Impedance, is it 8 or 16 ohms? (Driver specs.)
icon12.gif  4pi: B&C DE 250 Impedance, is it 8 or 16 ohms? [message #78786] Fri, 27 December 2013 18:39 Go to next message
dmeckstr is currently offline  dmeckstr
Messages: 5
Registered: December 2013
Location: Los Gatos
Esquire
Hi Wayne,

I noticed on the new version of the 4pi cross-over schematic that the tweeter is marked as 16 ohms. I wanted to confirm that with you (before I actually buy some Rolling Eyes).

Thanks again,

David
Re: 4pi: B&C DE 250 Impedance, is it 8 or 16 ohms? [message #78787 is a reply to message #78786] Fri, 27 December 2013 19:08 Go to previous messageGo to next message
Wayne Parham is currently offline  Wayne Parham
Messages: 18787
Registered: January 2001
Illuminati (33rd Degree)

No, the tweeter is 8Ω. The part you're referring to is Rs, which is a 16Ω, 10W resistor placed in shunt across the compression driver.

Re: 4pi: B&C DE 250 Impedance, is it 8 or 16 ohms? [message #78788 is a reply to message #78787] Fri, 27 December 2013 19:48 Go to previous messageGo to next message
dmeckstr is currently offline  dmeckstr
Messages: 5
Registered: December 2013
Location: Los Gatos
Esquire
Thanks Wayne,

I was just coming back on to say I looked at the schematic again and realized that there was a new part there. Also, I see a couple posts down you told someone you use the DE 250-8. :~
Re: 4pi: B&C DE 250 Impedance, is it 8 or 16 ohms? [message #78789 is a reply to message #78788] Sat, 28 December 2013 06:53 Go to previous messageGo to next message
Bill Epstein is currently offline  Bill Epstein
Messages: 1088
Registered: May 2009
Location: Smoky Mts. USA
Illuminati (2nd Degree)
Speaking of Ohms, I'm finally, with a lot of help from Professor Brown, building the 50 Watt Monoblocks. The 5K Hammond 1650R OPTs have 4, 8 and 16 Ohm taps. My 4 Pi 2226Js, are 16 Ohm and the DE-250s, as the OP discovered, are 8.

I'm going to have 8 and 16 Ohm outputs, which is best for the 4 Pis? I'd hate to lose 33% of the Wattage with too low an impedance.
Re: 4pi: B&C DE 250 Impedance, is it 8 or 16 ohms? [message #78790 is a reply to message #78789] Sat, 28 December 2013 08:58 Go to previous message
Wayne Parham is currently offline  Wayne Parham
Messages: 18787
Registered: January 2001
Illuminati (33rd Degree)

If the midwoofer is 16Ω, I'd probably choose the 16Ω tap.

Previous Topic: 4pi Speaker Plans, Please
Next Topic: Flanking subs and phase
Goto Forum:
  


Current Time: Sat Nov 23 07:30:03 CST 2024

Sponsoring Organizations

DIY Audio Projects
DIY Audio Projects
OddWatt Audio
OddWatt Audio
Pi Speakers
Pi Speakers
Prosound Shootout
Prosound Shootout
Miller Audio
Miller Audio
Tubes For Amps
TubesForAmps.com

Lone Star Audiofest