AudioRoundTable.com: Pi Speakers » 1pi or 2pi for surrounds?

Home » Sponsored » Pi Speakers » 1pi or 2pi for surrounds?

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: 1pi or 2pi for surrounds? [message #69211 is a reply to message #69207]

Sat, 27 August 2011 09:32

Wayne Parham
Messages: 18786
Registered: January 2001

Illuminati (33rd Degree)

I like to cut the port holes on the baffle so the port tube fits snugly in them. Cut the port to the proper lenth with a table saw and apply a thin film of white glue on the edge to protect it. Put white glue on the baffle edge where the port goes and press it in flush to the baffle, wiping off any excess glue.

I also like to paint the interior of the port. You can do that with an aerosol can before gluing it in or you can use a paintbrush after assembly. If you spray paint the inside of the port, protect the outside where the white glue will be using masking tape. The cardboard adheres best when it isn't covered with paint.

Report message to a moderator

[Message index]

		1pi or 2pi for surrounds? By: smokarz on Mon, 08 August 2011 08:52
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Mon, 08 August 2011 11:34
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 08 August 2011 11:49
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Mon, 08 August 2011 14:18
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 08 August 2011 14:46
		Re: 1pi or 2pi for surrounds? By: justphil on Tue, 09 August 2011 21:40
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 10 August 2011 07:52
		Re: 1pi or 2pi for surrounds? By: justphil on Wed, 10 August 2011 08:12
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 10 August 2011 09:59
		Re: 1pi or 2pi for surrounds? By: justphil on Wed, 10 August 2011 18:39
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 16 August 2011 12:32
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 16 August 2011 14:52
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 22 August 2011 10:02
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Mon, 22 August 2011 10:15
		Re: 1pi or 2pi for surrounds? By: smokarz on Fri, 26 August 2011 12:16
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Fri, 26 August 2011 12:40
		Re: 1pi or 2pi for surrounds? By: smokarz on Fri, 26 August 2011 12:46
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Fri, 26 August 2011 13:29
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 27 August 2011 08:26
		Re: 1pi or 2pi for surrounds? By: justphil on Sat, 27 August 2011 08:48
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Sat, 27 August 2011 09:32
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 27 August 2011 09:28
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 27 August 2011 09:36
		Re: 1pi or 2pi for surrounds? By: justphil on Sat, 27 August 2011 09:53
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 27 August 2011 10:27
		Re: 1pi or 2pi for surrounds? By: justphil on Sat, 27 August 2011 10:55
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 30 August 2011 21:55
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 30 August 2011 22:40
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 31 August 2011 08:54
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Wed, 31 August 2011 10:52
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 31 August 2011 12:20
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 06 September 2011 09:05
		Re: 1pi or 2pi for surrounds? By: justphil on Tue, 06 September 2011 09:24
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 06 September 2011 10:20
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 06 September 2011 12:50
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 06 September 2011 15:46
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 06 September 2011 20:24
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 06 September 2011 21:42
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 08 September 2011 10:10
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Thu, 08 September 2011 11:37
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 08 September 2011 15:06
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 10 September 2011 11:39
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Sat, 10 September 2011 16:32
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 12 September 2011 21:57
		Re: 1pi or 2pi for surrounds? By: jshupe on Wed, 08 January 2014 21:21
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 12 September 2011 21:58
		Re: 1pi or 2pi for surrounds? By: smokarz on Mon, 12 September 2011 22:01
		Re: 1pi or 2pi for surrounds? By: justphil on Tue, 13 September 2011 09:36
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 13 September 2011 09:57
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 13 September 2011 10:29
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 13 September 2011 10:59
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Tue, 13 September 2011 14:15
		Re: 1pi or 2pi for surrounds? By: smokarz on Tue, 13 September 2011 21:10
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 14 September 2011 21:08
		Re: 1pi or 2pi for surrounds? By: smokarz on Wed, 14 September 2011 21:17
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Wed, 14 September 2011 22:10
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 15 September 2011 07:39
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Thu, 15 September 2011 07:49
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 15 September 2011 08:14
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Thu, 15 September 2011 10:25
		Re: 1pi or 2pi for surrounds? By: smokarz on Thu, 15 September 2011 11:32
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Thu, 15 September 2011 12:35
		Helmholtz frequency of each model By: Wayne Parham on Fri, 16 September 2011 09:41
		Re: 1pi or 2pi for surrounds? By: smokarz on Fri, 16 September 2011 18:16
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Fri, 16 September 2011 19:30
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 17 September 2011 08:45
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Sat, 17 September 2011 09:00
		Re: 1pi or 2pi for surrounds? By: smokarz on Sat, 17 September 2011 09:16
		Re: 1pi or 2pi for surrounds? By: Wayne Parham on Sat, 17 September 2011 10:45

Previous Topic:	Flanking subs and phase
Next Topic:	Pi 3 or 4?

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Thu Nov 21 12:51:03 CST 2024