AudioRoundTable.com: Pi Speakers

Home » Sponsored » Pi Speakers » 4 pi, oh my! (pi 4)

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: 4 pi, oh my! [message #66278 is a reply to message #66257]

Wed, 23 February 2011 09:55

EL Jack
Messages: 5
Registered: February 2011

Esquire

Bill Epstein wrote on Tue, 22 February 2011 17:10

EL Jack wrote on Tue, 22 February 2011 13:48

All standard: Eminence drivers and the base crossovers.

I have previously built a small 2-way but the veneer was not entirely successful. I'll need some help to decide what to do, but I'm inclined to go with a basic black paint.

I think you'll find that painting plywood or MDF is more work than veneer.

For $75 you can buy a 4x8 sheet of NBL (no black line) walnut, cherry or oak veneer from tape-ease.com. One sheet will do the front, top and sides of both speakers. Use the method described by Bob Brines for gluing it on http://www.brinesacoustics.com/Pages/Articles/Cabinet_Construction/Construction.html

index.php?t=getfile&id=324&private=0

You don't have to trim with a router, a sharp block plane or even a utility knife will do fine to get within an 1/8th, then sand flush.

Enjoy! (and go JBL and B&C as soon as you can!)

Thanks Bill - as you've figured out, I'm "Mr Black" from AA, and please accept my thanks for pointing out these speakers to me.

I'll check out the veneer method you mention. I previously did it a much more difficult way (with the guidance of a friend who is a woodworker but not much of a finisher...).

Report message to a moderator

[Message index]

		4 pi, oh my! By: EL Jack on Mon, 21 February 2011 18:14
		Re: 4 pi, oh my! By: Wayne Parham on Mon, 21 February 2011 19:07
		Re: 4 pi, oh my! By: EL Jack on Mon, 21 February 2011 19:38
		Re: 4 pi, oh my! By: Matts on Mon, 21 February 2011 22:41
		Re: 4 pi, oh my! By: EL Jack on Tue, 22 February 2011 12:48
		Re: 4 pi, oh my! By: Wayne Parham on Tue, 22 February 2011 13:53
		Re: 4 pi, oh my! By: Bill Epstein on Tue, 22 February 2011 17:10
		Re: 4 pi, oh my! By: steve f on Wed, 23 February 2011 02:41
		Re: 4 pi, oh my! By: Bill Epstein on Wed, 23 February 2011 08:45
		Re: 4 pi, oh my! By: Wayne Parham on Wed, 23 February 2011 14:25
		Re: 4 pi, oh my! By: Matts on Wed, 23 February 2011 14:45
		Re: 4 pi, oh my! By: EL Jack on Wed, 23 February 2011 09:55
		Re: 4 pi, oh my! By: Bill Epstein on Wed, 23 February 2011 21:29
		Re: 4 pi, oh my! By: Matts on Tue, 22 February 2011 17:09
		Re: 4 pi, oh my! By: Psychoacoustic on Wed, 23 February 2011 21:45
		Re: 4 pi, oh my! By: Doc Jr 8156 on Thu, 24 February 2011 22:05
		Re: 4 pi, oh my! By: vinylvalet on Mon, 29 August 2011 08:56
		Re: 4 pi, oh my! By: Wayne Parham on Mon, 29 August 2011 09:57
		Re: 4 pi, oh my! By: vinylvalet on Tue, 30 August 2011 08:21
		Re: 4 pi, oh my! By: Wayne Parham on Tue, 30 August 2011 08:43
		Re: 4 pi, oh my! By: vinylvalet on Tue, 30 August 2011 09:29
		Re: 4 pi, oh my! By: Wayne Parham on Tue, 30 August 2011 13:10

Previous Topic:	4Pi Speaker Plans request
Next Topic:	crossover board assembly

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Mon Nov 25 02:13:23 CST 2024