AudioRoundTable.com: Pi Speakers » 4 Pi Design Questions

Home » Sponsored » Pi Speakers » 4 Pi Design Questions

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: 4 Pi Design Questions [message #62303 is a reply to message #61737]

Wed, 07 April 2010 21:17

Nichol1997
Messages: 21
Registered: December 2009
Location: Virginia

Chancellor

Wayne,
Thanks for your help. That answered a lot of my questions in regards to crossover components. However, I am trying to find a source for the 8-Ohm, 100 Watt non-inductive resistor. I found one that Parts Express offers but I am not sure if it is what I need because they call it a "dummy load resistor". Here is the link:
http://www.parts-express.com/pe/showdetl.cfm?Partnumber=019-020

Is this the correct one to use?
Is there a better brand that I should be considering since I will be upgrading all the other crossover components?

Report message to a moderator

[Message index]

		4 Pi Design Questions By: Nichol1997 on Sun, 17 January 2010 22:09
		Re: 4 Pi Design Questions By: Nichol1997 on Mon, 18 January 2010 06:36
		Re: 4 Pi Design Questions By: Wayne Parham on Mon, 18 January 2010 08:46
		Re: 4 Pi Design Questions By: Nichol1997 on Wed, 20 January 2010 20:59
		Re: 4 Pi Design Questions By: Wayne Parham on Wed, 20 January 2010 21:09
		Re: 4 Pi Design Questions By: Nichol1997 on Thu, 01 April 2010 21:15
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 02 April 2010 09:25
		Re: 4 Pi Design Questions By: Nichol1997 on Fri, 02 April 2010 20:58
		Re: 4 Pi Design Questions By: Wayne Parham on Sat, 03 April 2010 09:32
		Re: 4 Pi Design Questions By: Nichol1997 on Wed, 07 April 2010 21:17
		Re: 4 Pi Design Questions By: Wayne Parham on Wed, 07 April 2010 21:55
		Re: 4 Pi Design Questions By: Nichol1997 on Sun, 20 June 2010 08:18
		Re: 4 Pi Design Questions By: Wayne Parham on Sun, 20 June 2010 08:54
		Re: 4 Pi Design Questions By: Nichol1997 on Thu, 11 November 2010 21:11
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 12 November 2010 07:52
		Re: 4 Pi Design Questions By: Psychoacoustic on Thu, 11 November 2010 22:06
		Re: 4 Pi Design Questions By: Doc Jr 8156 on Fri, 12 November 2010 09:41
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 12 November 2010 14:44
		Re: 4 Pi Design Questions By: Nichol1997 on Thu, 17 May 2012 19:38
		Re: 4 Pi Design Questions By: Wayne Parham on Thu, 17 May 2012 22:46
		Re: 4 Pi Design Questions By: Nichol1997 on Fri, 01 June 2012 19:30
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 01 June 2012 21:35
		Re: 4 Pi Design Questions By: mantha3 on Sat, 02 June 2012 08:56
		Re: 4 Pi Design Questions By: Wayne Parham on Sat, 02 June 2012 10:30
		Re: 4 Pi Design Questions By: Nichol1997 on Mon, 18 June 2012 19:50
		Re: 4 Pi Design Questions By: Wayne Parham on Mon, 18 June 2012 21:12
		Re: 4 Pi Design Questions By: mantha3 on Tue, 19 June 2012 07:52
		Re: 4 Pi Design Questions By: Wayne Parham on Tue, 19 June 2012 07:55
		Re: 4 Pi Design Questions By: Nichol1997 on Tue, 19 June 2012 19:08
		Re: 4 Pi Design Questions By: Wayne Parham on Tue, 19 June 2012 21:34
		Re: 4 Pi Design Questions By: Nichol1997 on Sun, 24 June 2012 20:04
		Re: 4 Pi Design Questions By: Nichol1997 on Sun, 24 June 2012 20:08
		Re: 4 Pi Design Questions By: Wayne Parham on Mon, 25 June 2012 07:48
		Re: 4 Pi Design Questions By: mantha3 on Mon, 25 June 2012 17:15
		Re: 4 Pi Design Questions By: Wayne Parham on Mon, 25 June 2012 18:12
		Re: 4 Pi Design Questions By: mantha3 on Fri, 31 August 2012 15:13
		Cabinet design, port placement and internal standing waves By: Wayne Parham on Fri, 31 August 2012 18:28
		Re: 4 Pi Design Questions By: mantha3 on Fri, 31 August 2012 18:39
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 31 August 2012 18:51
		Re: Cabinet design, port placement and internal standing waves By: dheflin44 on Wed, 27 February 2013 15:16
		Re: Cabinet design, port placement and internal standing waves By: Wayne Parham on Wed, 27 February 2013 15:50
		Re: Cabinet design, port placement and internal standing waves By: dheflin44 on Wed, 27 February 2013 17:06
		Re: Cabinet design, port placement and internal standing waves By: Wayne Parham on Wed, 27 February 2013 17:25

Previous Topic:	2Pi's completed - now I want a center channel
Next Topic:	4Pi Plans for new HT build

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Tue Nov 26 22:30:28 CST 2024