AudioRoundTable.com: Pi Speakers » Two Tower initial impressions

Home » Sponsored » Pi Speakers » Two Tower initial impressions

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: Two Tower initial impressions [message #48278 is a reply to message #48265]

Mon, 21 November 2005 19:19

Norbert
Messages: 42
Registered: May 2009

Baron

I started using carpenter's glue... that didn't go well because I only have four clamps and a big piece of plywood to sandwich the veneer and I am certain I needed more... so for the rest of the project I used contact cement.. all of my bubles came after applying latex shallac over contact cement backed veneer. Speaking of veneer, I used the raw variety. Looking back I'll never use raw veneer again (although it was way cheaper compared to paper backed ones) and would need way more clamps... someone told me later that I also needed a roller to apply on the veneer when matting to the clued surface.
Bill, would you have any other suggestions?

Report message to a moderator

[Message index]

		Two Tower initial impressions By: Shane on Thu, 17 November 2005 09:58
		Re: Two Tower initial impressions By: Matts on Thu, 17 November 2005 10:32
		Re: Two Tower initial impressions By: Shane on Thu, 17 November 2005 11:09
		Re: Two Tower initial impressions By: Matts on Thu, 17 November 2005 13:36
		Re: Two Tower initial impressions By: Shane on Thu, 17 November 2005 13:46
		Re: Steve Browns tranny choice By: Bill Epstein on Sat, 19 November 2005 17:58
		Re: Steve Browns tranny choice By: Shane on Sat, 19 November 2005 18:20
		Re: Steve Browns tranny choice By: Wayne Parham on Sun, 20 November 2005 11:57
		Re: Steve Browns tranny choice By: Shane on Sun, 20 November 2005 13:18
		Re: Steve Browns tranny choice By: Wayne Parham on Sun, 20 November 2005 13:33
		Re: Two Tower initial impressions By: Wayne Parham on Thu, 17 November 2005 11:13
		Re: Two Tower initial impressions By: Shane on Thu, 17 November 2005 12:21
		Re: Two Tower initial impressions By: Shane on Thu, 17 November 2005 12:28
		Re: Two Tower initial impressions By: Wayne Parham on Thu, 17 November 2005 14:37
		Re: Two Tower initial impressions By: Matts on Thu, 17 November 2005 16:10
		Re: Lead Switch By: Shane on Thu, 17 November 2005 16:31
		Re: Lead Switch By: Matts on Thu, 17 November 2005 17:56
		Re: Lead Switch By: Shane on Thu, 17 November 2005 18:10
		Re: Two Tower initial impressions By: GarMan on Thu, 17 November 2005 12:06
		Re: levels By: Shane on Thu, 17 November 2005 18:09
		Re: Two Tower placement By: Shane on Thu, 17 November 2005 16:11
		Re: OK think I've got it. Royal Cable. By: Shane on Thu, 17 November 2005 18:07
		Re: Them's fghtin' words! By: Bill Epstein on Fri, 18 November 2005 14:43
		Re: Them's fghtin' words! By: Shane on Fri, 18 November 2005 16:25
		Re: Them's fghtin' words! By: GarMan on Fri, 18 November 2005 16:40
		Re: Them's fghtin' words! By: Shane on Fri, 18 November 2005 16:44
		Bill--question on cables, By: Shane on Sat, 19 November 2005 21:57
		Re: Hey Steve Brown, about those IC's? By: Bill Epstein on Sun, 20 November 2005 02:33
		I liked Royal Cable so much I bought the entire stock By: colinhester on Fri, 18 November 2005 23:22
		Re: Two Tower initial impressions By: Norbert on Sat, 19 November 2005 21:43
		Re: Two Tower initial impressions By: Shane on Sat, 19 November 2005 21:49
		Re: Two Tower initial impressions By: Norbert on Sun, 20 November 2005 09:19
		Re: Two Tower initial impressions By: Shane on Sun, 20 November 2005 10:26
		Re: Two Tower initial impressions By: Norbert on Mon, 21 November 2005 19:26
		speaker placement By: Shane on Mon, 21 November 2005 20:49
		Re: speaker placement By: Norbert on Mon, 21 November 2005 21:33
		Re: Two Tower initial impressions By: Bill Epstein on Sun, 20 November 2005 13:04
		Re: Two Tower initial impressions By: Norbert on Mon, 21 November 2005 19:19
		Re: Two Tower initial impressions By: Bill Epstein on Mon, 21 November 2005 20:08
		Re: Two Tower initial impressions By: Norbert on Mon, 21 November 2005 21:42
		Re: Two Tower initial impressions By: Bill Epstein on Tue, 22 November 2005 02:46

Previous Topic:	request for 2 pi bass reflex plans
Next Topic:	Request for wooden HF horn plans

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Jul 28 09:15:17 CDT 2024