AudioRoundTable.com: Pi Speakers » Damping 511B ringing: Whats your experience?

Home » Sponsored » Pi Speakers » Damping 511B ringing: Whats your experience?

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Answers found! Thanks [message #41275 is a reply to message #41274]

Thu, 08 May 2003 17:35

AstroSonic
Messages: 58
Registered: May 2009

Baron

Bill,
In the article on the small VOTT's, in the section on improving the horns, the first solution done by Altec was to place foam between the webs...that would be the 'fins' of the current discussion, and the foam was placed where the weld on the earlier models was right? The latex paint and sand idea also sounds like it would be very effective. Would you say that either method by itself would be sufficient? I had run into that article a few years ago and had forgotten how informative and useful it was.
Thanks again.
AstroSonic

Report message to a moderator

[Message index]

		Damping 511B ringing: Whats your experience? By: AstroSonic on Mon, 05 May 2003 10:34
		Re: Just say no to dope By: bmar on Mon, 05 May 2003 18:00
		Re: Just say no to dope By: AstroSonic on Wed, 07 May 2003 07:49
		Re: Just say no to dope By: bmar on Thu, 08 May 2003 12:14
		'Nother question on fin cutting By: JLapaire on Thu, 08 May 2003 05:59
		Re: Just slice them By: bmar on Thu, 08 May 2003 12:18
		Thanks (nt) By: JLapaire on Fri, 09 May 2003 02:58
		7)sell on ebay By: Sam P. on Tue, 06 May 2003 04:32
		Love'm or leave'm! By: AstroSonic on Wed, 07 May 2003 08:19
		Re: Damping 511B ringing: Whats your experience? By: djn on Wed, 07 May 2003 13:27
		Re: Damping 511B ringing: Whats your experience? By: tdc on Wed, 07 May 2003 15:04
		more on fin cutting By: tdc on Wed, 07 May 2003 16:35
		Re: more on fin cutting By: AstroSonic on Thu, 08 May 2003 10:09
		Re: more on fin cutting By: tdc on Thu, 08 May 2003 10:27
		Fin cutting - Just the welds! By: AstroSonic on Thu, 08 May 2003 11:12
		Re: Fin cutting - Just the welds! By: tdc on Thu, 08 May 2003 12:38
		Depleted uranium and radial tire rubber By: Wayne Parham on Thu, 08 May 2003 13:02
		Re: Depleted uranium and radial tire rubber By: tdc on Thu, 08 May 2003 13:36
		Re: Depleted uranium and radial tire rubber By: Wayne Parham on Thu, 08 May 2003 13:50
		Breakup modes and crossover points By: Wayne Parham on Thu, 08 May 2003 12:59
		Anyone tried Dynamat? By: AstroSonic on Thu, 08 May 2003 09:11
		Re: Yes, Dynamat Xtreme By: Matts on Sun, 11 May 2003 10:07
		Re: Yes, Dynamat Xtreme By: AstroSonic on Mon, 12 May 2003 14:29
		As usual, we have the answers........ By: BillEpstein on Thu, 08 May 2003 16:38
		Answers found! Thanks By: AstroSonic on Thu, 08 May 2003 17:35
		Re: Answers found! Thanks By: AskBill on Thu, 08 May 2003 17:54

Previous Topic:	Where can I Buy some nice BIG CD horns???
Next Topic:	MAF photos

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sat Nov 30 03:39:31 CST 2024