AudioRoundTable.com: Pi Speakers » Piezos / 2 way designs

Home » Sponsored » Pi Speakers » Piezos / 2 way designs

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: Thanks, you make a very strong agument for this driver! [message #33345 is a reply to message #33343]

Fri, 11 May 2001 18:12

Paul C.
Messages: 218
Registered: May 2009

Master

My Pyles are some older models, MH1560, no longer catalogged, at least not under that number. These are 15" musical inst / PA woofers.

I have used these in several cabinets and with several horns. But the easiest to use, by far, are the CTS-Motorolas.

The 1188's I have sound very good. Yes, I wish I had a response graph to look at, but my ears tell me they are just fine.

According to what I found on the CTS site, and talking to Mr. Moleski today, wire a 20 ohm 10 wt resistor in series with the 1188's. The 1188's also have the same Powerline protection circuit as the KSN1165, 1142, etc. The various 1800 hz Powerline drivers need no outboard resistors, or other parts of any sort.

Report message to a moderator

[Message index]

		Piezos / 2 way designs By: Paul C. on Wed, 09 May 2001 12:00
		Re: Piezos / 2 way designs By: Paul C. on Wed, 09 May 2001 12:19
		Re: Piezos / 2 way designs By: Stan C. on Wed, 09 May 2001 12:32
		Re: Piezos / 2 way designs By: Paul C. on Wed, 09 May 2001 14:09
		Re: Piezos / 2 way designs By: Paul C. on Sun, 20 May 2001 07:56
		Re: Piezos / 2 way designs By: Crazy Dave on Thu, 10 May 2001 12:48
		Re: Piezos / 2 way designs By: Paul C. on Thu, 10 May 2001 13:31
		Re: Thanks, you make a very strong agument for this driver! NT By: Crazy Dave on Thu, 10 May 2001 15:50
		Re: Thanks, you make a very strong agument for this driver! NT By: Paul C. on Thu, 10 May 2001 19:04
		Re: Thanks, you make a very strong agument for this driver! By: Crazy Dave on Fri, 11 May 2001 12:36
		Re: Thanks, you make a very strong agument for this driver! By: Paul C. on Fri, 11 May 2001 18:12
		Re: Thanks, you make a very strong agument for this driver! By: Crazy Dave on Sat, 12 May 2001 22:53
		Re: Thanks, you make a very strong agument for this driver! By: Paul C. on Sun, 13 May 2001 01:58
		Re: I hope everyone interested in piezos reads this whole thread By: Crazy Dave on Mon, 14 May 2001 11:25
		Re: I hope everyone interested in piezos reads this whole thread By: Paul C. on Mon, 14 May 2001 12:47
		Re: Sounds great! It may be getting time for me to break out the table saw. NT By: Crazy Dave on Mon, 14 May 2001 13:44
		Re: Sounds great! It may be getting time for me to break out the table saw. NT By: Paul C. on Mon, 14 May 2001 16:39
		Re: Sounds great! It may be getting time for me to break out the table saw. NT By: Crazy Dave on Tue, 15 May 2001 09:15
		Re: Sounds great! It may be getting time for me to break out the table saw. NT By: Paul C. on Tue, 15 May 2001 11:23
		Re: Sounds great! It may be getting time for me to break out the table saw. NT By: Crazy Dave on Wed, 16 May 2001 09:46
		Re: Sounds great! It may be getting time for me to break out the table saw. NT By: Paul C. on Tue, 15 May 2001 11:59
		Lens info!!! By: Paul C. on Fri, 11 May 2001 10:49
		Re: Piezos / 2 way designs By: DJ Z on Mon, 14 May 2001 17:09
		Re: Piezos / 2 way designs By: Jon Risch on Wed, 16 May 2001 23:39

Previous Topic:	Stage monitors -- doubled Pi 4s?
Next Topic:	Pi implementations of quartz piezoelectric tweeters

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sat Nov 23 17:26:00 CST 2024