AudioRoundTable.com: Speaker » Tell Us About the Array you built or are building......

Home » Audio » Speaker » Tell Us About the Array you built or are building......

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: Tell Us About the Array you built or are building...... [message #23482 is a reply to message #23480]

Mon, 26 February 2007 10:41

Ivor the Engine Driver is currently offline

Ivor the Engine Driver
Messages: 18
Registered: May 2009

Chancellor

I'm using the rear flange neos. Trimming the flange bumps the theoretical combing problem to around 9500, IIRC. In practice, though, I've never heard it when not doing freq sweeps. This could be due to several factors: the steep roll-off in my hearing above 10k due to a lifetime of exposure to rock concerts and unmuffled race cars (I think a three-rotor Mazda GTP car was the tipping point); the relatively low frequencies in the music I usually listen to (rock/blues); and because I am almost always doing something and moving around when listening to the arrays, which are in the heated portion of my shop.

Report message to a moderator

[Message index]

		Tell Us About the Array you built or are building...... By: Marlboro on Thu, 22 February 2007 07:56
		Re: Tell Us About the Array you built or are building...... By: Eric on Thu, 22 February 2007 12:00
		Re: Tell Us About the Array you built or are building...... By: Marlboro on Thu, 22 February 2007 16:26
		Re: Tell Us About the Array you built or are building...... By: Eric on Thu, 22 February 2007 17:08
		Re: Tell Us About the Array you built or are building...... By: Marlboro on Thu, 22 February 2007 17:57
		Marlboro Tubes By: Eric on Fri, 23 February 2007 09:11
		Re: Tell Us About the Array you built or are building...... By: FredT on Fri, 23 February 2007 06:48
		Re: Tell Us About the Array you built or are building...... By: Rick Craig on Fri, 23 February 2007 06:57
		Re: Tell Us About the Array you built or are building...... By: jamesk on Sun, 10 June 2007 04:45
		Re: Tell Us About the Array you built or are building...... By: Ivor the Engine Driver on Mon, 26 February 2007 10:04
		Re: Tell Us About the Array you built or are building...... By: Ivor the Engine Driver on Mon, 26 February 2007 10:07
		Re: Tell Us About the Array you built or are building...... By: Marlboro on Mon, 26 February 2007 10:20
		Re: Tell Us About the Array you built or are building...... By: Ivor the Engine Driver on Mon, 26 February 2007 10:41
		Re: Tell Us About the Array you built or are building...... By: Marlboro on Mon, 26 February 2007 13:16
		Re: Tell Us About the Array you built or are building...... By: Ivor the Engine Driver on Mon, 26 February 2007 13:34
		Humor: the best medicine: Thanks By: Marlboro on Mon, 26 February 2007 15:01
		So, you're conceding my points? -nt- By: Ivor the Engine Driver on Mon, 26 February 2007 15:51
		Rah Rah Bis Boom Bah! By: Marlboro on Mon, 26 February 2007 16:27
		wiki definition By: pauly on Mon, 26 February 2007 18:48
		Who knew? By: Ivor the Engine Driver on Tue, 27 February 2007 08:17
		ART Rules By: admin on Wed, 28 February 2007 09:06
		Re: ART Rules By: Ivor the Engine Driver on Wed, 28 February 2007 10:51
		Re: ART Rules By: admin on Wed, 28 February 2007 14:43
		Re: Tell Us About the Array you built or are building...... By: hot.rod.audio on Thu, 01 March 2007 09:11
		Re: Tell Us About the Array you built or are building...... By: Stephen Narayan on Sun, 01 April 2007 00:30
		What Crossover Frequency? By: Marlboro on Sun, 01 April 2007 07:40
		Re: Tell Us About the Array you built or are building...... By: Marlboro on Sun, 01 April 2007 08:35
		Re: Tell Us About the Array you built or are building...... By: Stephen Narayan on Thu, 26 April 2007 21:07

Previous Topic:	Even more on slam - and imaging!
Next Topic:	Relationship Between X Max And Efficiency Questions

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Fri Jul 12 03:21:11 CDT 2024