AudioRoundTable.com: Pi Speakers » 4pi flat pack, Rhino Line

Home » Sponsored » Pi Speakers » 4pi flat pack, Rhino Line

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: 4pi flat pack, Rhino Line [message #92301 is a reply to message #92299]

Wed, 09 September 2020 14:15

jtwrace
Messages: 66
Registered: October 2009
Location: FL

Viscount

Wayne Parham wrote on Wed, 09 September 2020 14:09

Looks great! You inserted your T-Nuts exactly the same way I do - With a dab of glue to hold 'em in.

Thanks for the build thread!

Glad it's Wayne approved! Now I await the Pi 4 kit to document each and every step as a build guide. Wink

Report message to a moderator

Re: 4pi flat pack, Rhino Line [message #92302 is a reply to message #92301]

Wed, 09 September 2020 17:22

Wayne Parham
Messages: 18786
Registered: January 2001

Illuminati (33rd Degree)

I'm anxious to see Sean's build too. I'll bet he'd be happy to get the same look as you did on your subs. You really did a good job and I'm sure he appreciated the tips.

Report message to a moderator

Re: 4pi flat pack, Rhino Line [message #92303 is a reply to message #92302]

Wed, 09 September 2020 17:38

jtwrace
Messages: 66
Registered: October 2009
Location: FL

Viscount

Wayne Parham wrote on Wed, 09 September 2020 17:22

I'm anxious to see Sean's build too. I'll bet he'd be happy to get the same look as you did on your subs. You really did a good job and I'm sure he appreciated the tips.

Guess you missed my intent Laughing

I do look forward to his build though.

Report message to a moderator

Re: 4pi flat pack, Rhino Line [message #92304 is a reply to message #92303]

Wed, 09 September 2020 21:27

rage889
Messages: 3
Registered: September 2020

Esquire

I'm impressed you made that Duratex look so good!

I was tempted to go that route - but laziness prevailed and I dropped the assembled cabs off to the local Rhino liner today. I'm guessing cost will be about Double the diy route - hopefully the results are as good as what you did!

I like the choice of neutrik connector as well - that is also a tempting option here.

Report message to a moderator

Re: 4pi flat pack, Rhino Line [message #92305 is a reply to message #92304]

Wed, 09 September 2020 21:30

jtwrace
Messages: 66
Registered: October 2009
Location: FL

Viscount

rage889 wrote on Wed, 09 September 2020 21:27

I'm impressed you made that Duratex look so good!

I was tempted to go that route - but laziness prevailed and I dropped the assembled cabs off to the local Rhino liner today. I'm guessing cost will be about Double the diy route - hopefully the results are as good as what you did!

I like the choice of neutrik connector as well - that is also a tempting option here.

Go get them back! You'll need a half gallon of duratex and one roller. The cleanup is so easy with Duratex it's silly. The Neutrik is just nice and simple without any wires falling out ever. I like them when possible.

If you really are going to add the Neutrik, I really suggest you do it before paint though. It would really suck to have an "oops" on a finished cabinet.

Report message to a moderator

Re: 4pi flat pack, Rhino Line [message #92323 is a reply to message #92291]

Tue, 15 September 2020 16:05

tubino
Messages: 13
Registered: May 2009

Chancellor

Thanks for posting these details! It's very useful for me. Did you use 10-32 for the t-nuts, or 1/4" x 20?

Report message to a moderator

Re: 4pi flat pack, Rhino Line [message #92325 is a reply to message #92323]

Tue, 15 September 2020 16:14

jtwrace
Messages: 66
Registered: October 2009
Location: FL

Viscount

tubino wrote on Tue, 15 September 2020 16:05

Thanks for posting these details! It's very useful for me. Did you use 10-32 for the t-nuts, or 1/4" x 20?

1/4"-20 Tee Nuts for my driver. However, if you are using a small Waveguide or driver you can use 10-32 without an issue. Overkill is usually good; however, the bolt still needs to go through the trim ring. Wink

Report message to a moderator