AudioRoundTable.com: Radio » Switching channels solution

Home » Audio » Radio » Switching channels solution

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Switching channels solution [message #83843]

Mon, 31 October 2016 10:02

Rodial
Messages: 20
Registered: August 2016

Chancellor

Recently, I've been getting this problem more often. The radio channels will start jumping and I will end up with a cross-breed of 2-3 channels. Is there any simple way to fix this?

Report message to a moderator

Re: Switching channels solution [message #83848 is a reply to message #83843]

Tue, 01 November 2016 21:32

gofar99
Messages: 1949
Registered: May 2010
Location: Southern Arizona

Illuminati (5th Degree)

Hi, What is the equipment?

Good Listening
Bruce

Report message to a moderator

Re: Switching channels solution [message #83855 is a reply to message #83843]

Thu, 03 November 2016 08:44

Rodial
Messages: 20
Registered: August 2016

Chancellor

I am not quite sure about the specifics but it is a regular dash receiver that came fitted in my car. The brand is Pioneer.

Report message to a moderator

Re: Switching channels solution [message #83865 is a reply to message #83855]

Thu, 03 November 2016 17:45

gofar99
Messages: 1949
Registered: May 2010
Location: Southern Arizona

Illuminati (5th Degree)

That is rather odd. Based on how a lot of gear works I suspect either voltage fluctuation or interference. I would rate the voltage issue more likely though. It is likely that there is some sort of power filtering in the unit or in the wiring going to it. That would be the first place to check. A bad ground connection there might cause the problems. A bad filter could also introduce EMI into the unit and fool it into thinking it was some sort of change signal. If the unit has remote control capability then it is also possible that something is tricking it into changing. I know these are rather general concepts and the average person will not be able to check on them. I would expect that the best way to solve the problem is to take it in for service. Likely a costly experience. It might be cheaper to just replace it.

Good Listening
Bruce

Report message to a moderator

Re: Switching channels solution [message #83892 is a reply to message #83843]

Sun, 06 November 2016 06:55

Rodial
Messages: 20
Registered: August 2016

Chancellor

You are absolutely right about these concepts being a bit challenging for someone like myself. I'll look to see what its replacement will cost me; if, like you had mentioned, it's on the higher side, I'll just leave it alone as it doesn't bug me enough to justify a costly replacement.

Report message to a moderator

Re: Switching channels solution [message #84201 is a reply to message #83892]

Tue, 27 December 2016 10:50

Azuri
Messages: 315
Registered: November 2012

Grand Master

With the electrical systems in cars getting more complex, I can see this being a common issue. Cross-overs of 2 to 3 channels doesn't sound like the typical outside interference.

Report message to a moderator

Re: Switching channels solution [message #84202 is a reply to message #84201]

Tue, 27 December 2016 15:45

Wayne Parham
Messages: 18787
Registered: January 2001

Illuminati (33rd Degree)

I think Bruce was suggesting looking into the common problems that you can check. Check the power, check the ground. Possibly consider adding a series coil and a shunt capacitor on the power line to reduce noise. Check that wiring isn't frayed.

It's really hard to tell what's going on inside the radio without an oscilloscope. And even then, a digital problem requires some kind of digital analyzer like a debugger.

Basically, something like this is hard to troubleshoot because of the lack of visibility in the internal mechanism(s). Looking for things like bad connections and ground loops are always good suggestions, but beyond that, it's probably best to swap the radio.

Report message to a moderator

Previous Topic:	Amos and Andy
Next Topic:	How has radio changed over the years?

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sat Nov 23 20:57:06 CST 2024