AudioRoundTable.com: Pi Speakers

Home » Sponsored » Pi Speakers » 4 PI by Andy

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: 4 PI by Andy [message #74057 is a reply to message #74041]

Thu, 04 October 2012 07:24

mantha3
Messages: 72
Registered: May 2012
Location: Lino Lakes, MN

Viscount

Wow! My crossovers are suddenly looking really ugly! Even more in comparision to what you have! Oh well.. The solder points are solid and it is to the schematic. I'll hide them in the speaker where nobody will know.

I stood up the .5 and left the 1.0 and 1.5 flat. the 1.0 and the 1.5 are about 4" from one another so I should be good. I say this from a "How To" write up on Parts Express for how to build a cross over. In this it is said the 3-4" in apart range is where the magnetic interference is no longer an issue.

Either way.. I could pull off the .5 inducer... I don't think I could pull off the 1.0 or 1.5. These 14ga are big and held down with lots of glue. I could hardly pull off the .5 ones.

I'll be building in a few weeks and I'll come back with updates.

This will be gradual.

PS - I would have purchased the parts from you Wayne but I got them some time ago.... When you were out of the Eminence horns and 2226 woofers. I was planning to build in the Summer/Early Fall but just too busy.

Report message to a moderator

[Message index]

		4 PI by Andy By: mantha3 on Wed, 03 October 2012 07:48
		Re: 4 PI by Andy By: mantha3 on Wed, 03 October 2012 08:04
		Re: 4 PI by Andy By: mantha3 on Wed, 03 October 2012 12:48
		Re: 4 PI by Andy By: Wayne Parham on Wed, 03 October 2012 13:14
		Re: 4 PI by Andy By: mantha3 on Wed, 03 October 2012 15:56
		Re: 4 PI by Andy By: mantha3 on Wed, 03 October 2012 16:22
		Re: 4 PI by Andy By: Wayne Parham on Wed, 03 October 2012 16:35
		Re: 4 PI by Andy By: mantha3 on Wed, 03 October 2012 17:52
		Re: 4 PI by Andy By: Wayne Parham on Wed, 03 October 2012 17:55
		Re: 4 PI by Andy By: mantha3 on Wed, 03 October 2012 18:00
		Re: 4 PI by Andy By: Wayne Parham on Wed, 03 October 2012 20:05
		Re: 4 PI by Andy By: mantha3 on Thu, 04 October 2012 07:24
		Re: 4 PI by Andy By: mantha3 on Sat, 03 November 2012 09:26
		Re: 4 PI by Andy By: mantha3 on Sat, 03 November 2012 09:30
		Re: 4 PI by Andy By: zheka on Sat, 03 November 2012 14:56
		Re: 4 PI by Andy By: mantha3 on Sat, 03 November 2012 16:39
		Re: 4 PI by Andy By: Wayne Parham on Sat, 03 November 2012 20:57
		Re: 4 PI by Andy By: mantha3 on Sun, 04 November 2012 16:14
		Re: 4 PI by Andy By: mantha3 on Sat, 10 November 2012 07:49
		Re: 4 PI by Andy By: Wayne Parham on Sat, 10 November 2012 10:04
		Re: 4 PI by Andy By: mantha3 on Sat, 10 November 2012 11:04
		Re: 4 PI by Andy By: zheka on Sun, 20 January 2013 09:25
		Re: 4 PI by Andy By: Wayne Parham on Sun, 20 January 2013 13:01
		Re: 4 PI by Andy By: zheka on Sun, 20 January 2013 13:41
		Re: 4 PI by Andy By: Wayne Parham on Sun, 20 January 2013 17:11
		Re: 4 PI by Andy By: mantha3 on Thu, 18 April 2013 13:01
		Re: 4 PI by Andy By: Wayne Parham on Thu, 18 April 2013 18:36
		Re: 4 PI by Andy By: mantha3 on Thu, 18 April 2013 19:55
		Re: 4 PI by Andy By: mantha3 on Thu, 18 April 2013 19:58
		Re: 4 PI by Andy By: Wayne Parham on Fri, 19 April 2013 00:02
		Re: 4 PI by Andy By: mantha3 on Fri, 19 April 2013 11:57
		Re: 4 PI by Andy By: Wayne Parham on Fri, 19 April 2013 12:56
		Re: 4 PI by Andy By: zheka on Sat, 10 November 2012 13:55
		Re: 4 PI by Andy By: zheka on Sat, 10 November 2012 14:00
		Re: 4 PI by Andy By: Wayne Parham on Sat, 10 November 2012 22:33
		Re: 4 PI by Andy By: mantha3 on Sun, 11 November 2012 08:15
		Re: 4 PI by Andy By: Wayne Parham on Sun, 11 November 2012 10:53
		Re: 4 PI by Andy By: mantha3 on Wed, 14 November 2012 19:59
		Re: 4 PI by Andy By: mantha3 on Fri, 07 December 2012 08:28
		Re: 4 PI by Andy By: zheka on Fri, 07 December 2012 08:49
		Re: 4 PI by Andy By: zheka on Sun, 20 January 2013 14:01

Previous Topic:	2 pi tower folding?
Next Topic:	4 Pi plans

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Fri Nov 22 16:44:33 CST 2024