AudioRoundTable.com: Pi Speakers » 4 Pi Design Questions

Home » Sponsored » Pi Speakers » 4 Pi Design Questions

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: 4 Pi Design Questions [message #72745 is a reply to message #64658]

Thu, 17 May 2012 19:38

Nichol1997
Messages: 21
Registered: December 2009
Location: Virginia

Chancellor

I finally got around to measuring my modified Pi4 speakers. Attached is the nearfield frequency response using Room Eq Wizard version 5.

I am still learning how to use the software and hardware so I am not sure if I am measuring it correctly. I had the mic mounted on a stand that was 16" from the baffle and just a little bit below the throat of the compression driver on the vertical.

My measurement gear consists of:
HP laptop w/ Windows XP
MobilePre USB external soundcard
Behringer ECM8000 mic
Behringer EP2500 (ran the MobilePre USB directly to the amp)

To me, the measurement makes it look like my woofers are out of phase. I only measured the right speaker. I will have to wait until it is quiet in the house again before I can measure the left speaker.

Attachment: Pi4 Measurement.jpg
(Size: 90.03KB, Downloaded 490 times)

Report message to a moderator

[Message index]

		4 Pi Design Questions By: Nichol1997 on Sun, 17 January 2010 22:09
		Re: 4 Pi Design Questions By: Nichol1997 on Mon, 18 January 2010 06:36
		Re: 4 Pi Design Questions By: Wayne Parham on Mon, 18 January 2010 08:46
		Re: 4 Pi Design Questions By: Nichol1997 on Wed, 20 January 2010 20:59
		Re: 4 Pi Design Questions By: Wayne Parham on Wed, 20 January 2010 21:09
		Re: 4 Pi Design Questions By: Nichol1997 on Thu, 01 April 2010 21:15
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 02 April 2010 09:25
		Re: 4 Pi Design Questions By: Nichol1997 on Fri, 02 April 2010 20:58
		Re: 4 Pi Design Questions By: Wayne Parham on Sat, 03 April 2010 09:32
		Re: 4 Pi Design Questions By: Nichol1997 on Wed, 07 April 2010 21:17
		Re: 4 Pi Design Questions By: Wayne Parham on Wed, 07 April 2010 21:55
		Re: 4 Pi Design Questions By: Nichol1997 on Sun, 20 June 2010 08:18
		Re: 4 Pi Design Questions By: Wayne Parham on Sun, 20 June 2010 08:54
		Re: 4 Pi Design Questions By: Nichol1997 on Thu, 11 November 2010 21:11
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 12 November 2010 07:52
		Re: 4 Pi Design Questions By: Psychoacoustic on Thu, 11 November 2010 22:06
		Re: 4 Pi Design Questions By: Doc Jr 8156 on Fri, 12 November 2010 09:41
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 12 November 2010 14:44
		Re: 4 Pi Design Questions By: Nichol1997 on Thu, 17 May 2012 19:38
		Re: 4 Pi Design Questions By: Wayne Parham on Thu, 17 May 2012 22:46
		Re: 4 Pi Design Questions By: Nichol1997 on Fri, 01 June 2012 19:30
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 01 June 2012 21:35
		Re: 4 Pi Design Questions By: mantha3 on Sat, 02 June 2012 08:56
		Re: 4 Pi Design Questions By: Wayne Parham on Sat, 02 June 2012 10:30
		Re: 4 Pi Design Questions By: Nichol1997 on Mon, 18 June 2012 19:50
		Re: 4 Pi Design Questions By: Wayne Parham on Mon, 18 June 2012 21:12
		Re: 4 Pi Design Questions By: mantha3 on Tue, 19 June 2012 07:52
		Re: 4 Pi Design Questions By: Wayne Parham on Tue, 19 June 2012 07:55
		Re: 4 Pi Design Questions By: Nichol1997 on Tue, 19 June 2012 19:08
		Re: 4 Pi Design Questions By: Wayne Parham on Tue, 19 June 2012 21:34
		Re: 4 Pi Design Questions By: Nichol1997 on Sun, 24 June 2012 20:04
		Re: 4 Pi Design Questions By: Nichol1997 on Sun, 24 June 2012 20:08
		Re: 4 Pi Design Questions By: Wayne Parham on Mon, 25 June 2012 07:48
		Re: 4 Pi Design Questions By: mantha3 on Mon, 25 June 2012 17:15
		Re: 4 Pi Design Questions By: Wayne Parham on Mon, 25 June 2012 18:12
		Re: 4 Pi Design Questions By: mantha3 on Fri, 31 August 2012 15:13
		Cabinet design, port placement and internal standing waves By: Wayne Parham on Fri, 31 August 2012 18:28
		Re: 4 Pi Design Questions By: mantha3 on Fri, 31 August 2012 18:39
		Re: 4 Pi Design Questions By: Wayne Parham on Fri, 31 August 2012 18:51
		Re: Cabinet design, port placement and internal standing waves By: dheflin44 on Wed, 27 February 2013 15:16
		Re: Cabinet design, port placement and internal standing waves By: Wayne Parham on Wed, 27 February 2013 15:50
		Re: Cabinet design, port placement and internal standing waves By: dheflin44 on Wed, 27 February 2013 17:06
		Re: Cabinet design, port placement and internal standing waves By: Wayne Parham on Wed, 27 February 2013 17:25

Previous Topic:	2Pi's completed - now I want a center channel
Next Topic:	4Pi Plans for new HT build

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Wed Nov 27 01:21:59 CST 2024