AudioRoundTable.com: Pi Speakers

Home » Sponsored » Pi Speakers » Cutting a circle

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Cutting a circle [message #44559]

Mon, 03 May 2004 12:48

Tom Flahavan
Messages: 13
Registered: May 2009

Chancellor

I am building studio towers. I need a tip on cutting out the 9 1/8 inch circle. How do you make it perfect? I am useing a hole saw for the 2 3/4 and the 4 1/2 inch cuts. Any tricks out there?

Report message to a moderator

Re: Cutting a circle [message #44560 is a reply to message #44559]

Mon, 03 May 2004 13:30

Wayne Parham
Messages: 18784
Registered: January 2001

Illuminati (33rd Degree)

Use a hole cutter like this:

Tool shops have 'em in various sizes, so you can probably find one locally. But it is sometimes hard to find cutters that go bigger than 8". Many of them use a sling blade, and I like that approach but you don't find those going very large. Click on the photo above and you can buy a tool that cuts holes up to 12" for sixty bucks.

Report message to a moderator

Re: Jasper Jig [message #44562 is a reply to message #44559]

Mon, 03 May 2004 15:41

Matts
Messages: 359
Registered: May 2009

Grand Master

If you have a router, get a Jasper Jig- it will cut perfect circles easily. Totally accurate and very easy to use. They sell them at Parts Express and buches of other places.

Report message to a moderator

Re: Cutting a circle [message #44564 is a reply to message #44559]

Mon, 03 May 2004 16:26

Tightwad
Messages: 41
Registered: May 2009

Baron

Carefully mark the circle.

Use a jigsaw, but err a bit on the inside.

Use a rasp to get the rest.

Report message to a moderator

Re: Fer a buck 2 skeventy-eight you can buy....... [message #44566 is a reply to message #44560]

Mon, 03 May 2004 20:13

BillEpstein
Messages: 886
Registered: May 2009

Illuminati (2nd Degree)

.....a scrap piece of 1/4" plywood and a nail.
That plastic or phenolic or whatever base on your router is designed to be removable.
Take it off, copy the screw hole placement onto the 15 or 20 inch long piece of plywood by wide enough to hold the screws for the base. Use your 2 1/2" hole saw to make the hole for the router bit and attach the plywood (it is now officially called a Trammel) to the router.
Draw the circle with a compass. Put the outside edge of the cutting bit on the circle and find the center, mark it on the trammel and push a nail through the trammel and into the center hole. Push, plunge or whatveer the router into the wood, rotate.
Or do what I did, as per Wayne's advice, having made too many trammels over the years I got lazy and bought the Jasper.

Report message to a moderator

Re: Cutting a circle [message #44569 is a reply to message #44559]

Tue, 04 May 2004 13:25

jeffh
Messages: 6
Registered: May 2009

Esquire

A router and circle jig is the best way. However, I now a good router will cost at least $100 and then $20+ for a circle jig. See my attached link to see my router, Jasper jig and homemade jig. I have attached a link to a subwoofer that I built. Just go to page 3 and you'll see the jigs.
http://europa70.tripod.com/diy_sonosub001.htm

Report message to a moderator

Re: Cutting a circle [message #44583 is a reply to message #44559]

Sat, 08 May 2004 08:35

Adrian Mack
Messages: 568
Registered: May 2009

Illuminati (1st Degree)

Of course you can use a router as some have suggested, but unless your flush mounting the drivers where you need to make a rebate, then a jigsaw will work fine. Mark the hole out with a compass and pencil, and cut it out with a jigsaw - since the driver mounts from the front, you cant see if the hole is slightly imperfect and it wont affect anything if it is, you'll be cutting right on the line anyway.

Jigsaws in Australia cost as little as AU$20, so I'd guess thats about US$17. You dont need a fancy one, the cheapest one available will work.

Report message to a moderator

Previous Topic:	Hey everyone!
Next Topic:	7 PI profess'l series w / 10 in. mid plans

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Mon Nov 18 15:39:04 CST 2024