AudioRoundTable.com: Pi Speakers » Damping 511B ringing: Whats your experience?

Home » Sponsored » Pi Speakers » Damping 511B ringing: Whats your experience?

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: Fin cutting - Just the welds! [message #41269 is a reply to message #41266]

Thu, 08 May 2003 12:38

tdc
Messages: 34
Registered: May 2009

Baron

I did all the steps more or less at once. I did not conduct extensive listing test with each step progress. There is some improvement but its not like going from a bad crossover to a perfect one. When you strike the horn after all the above is done there is a dull lower thud and you know its dampened. You could also use the horn to make a cast and then pour the cast with depleated uranium from surplus operation Iraqi Freedom shells. Now that would be dead. tdc

Report message to a moderator

[Message index]

		Damping 511B ringing: Whats your experience? By: AstroSonic on Mon, 05 May 2003 10:34
		Re: Just say no to dope By: bmar on Mon, 05 May 2003 18:00
		Re: Just say no to dope By: AstroSonic on Wed, 07 May 2003 07:49
		Re: Just say no to dope By: bmar on Thu, 08 May 2003 12:14
		'Nother question on fin cutting By: JLapaire on Thu, 08 May 2003 05:59
		Re: Just slice them By: bmar on Thu, 08 May 2003 12:18
		Thanks (nt) By: JLapaire on Fri, 09 May 2003 02:58
		7)sell on ebay By: Sam P. on Tue, 06 May 2003 04:32
		Love'm or leave'm! By: AstroSonic on Wed, 07 May 2003 08:19
		Re: Damping 511B ringing: Whats your experience? By: djn on Wed, 07 May 2003 13:27
		Re: Damping 511B ringing: Whats your experience? By: tdc on Wed, 07 May 2003 15:04
		more on fin cutting By: tdc on Wed, 07 May 2003 16:35
		Re: more on fin cutting By: AstroSonic on Thu, 08 May 2003 10:09
		Re: more on fin cutting By: tdc on Thu, 08 May 2003 10:27
		Fin cutting - Just the welds! By: AstroSonic on Thu, 08 May 2003 11:12
		Re: Fin cutting - Just the welds! By: tdc on Thu, 08 May 2003 12:38
		Depleted uranium and radial tire rubber By: Wayne Parham on Thu, 08 May 2003 13:02
		Re: Depleted uranium and radial tire rubber By: tdc on Thu, 08 May 2003 13:36
		Re: Depleted uranium and radial tire rubber By: Wayne Parham on Thu, 08 May 2003 13:50
		Breakup modes and crossover points By: Wayne Parham on Thu, 08 May 2003 12:59
		Anyone tried Dynamat? By: AstroSonic on Thu, 08 May 2003 09:11
		Re: Yes, Dynamat Xtreme By: Matts on Sun, 11 May 2003 10:07
		Re: Yes, Dynamat Xtreme By: AstroSonic on Mon, 12 May 2003 14:29
		As usual, we have the answers........ By: BillEpstein on Thu, 08 May 2003 16:38
		Answers found! Thanks By: AstroSonic on Thu, 08 May 2003 17:35
		Re: Answers found! Thanks By: AskBill on Thu, 08 May 2003 17:54

Previous Topic:	Where can I Buy some nice BIG CD horns???
Next Topic:	MAF photos

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Wed Jun 26 11:57:18 CDT 2024