AudioRoundTable.com: Craftsmen » PI four enclosure

Home » Audio » Craftsmen » PI four enclosure

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

PI four enclosure [message #29591]

Sun, 04 September 2005 15:51

beto1
Messages: 36
Registered: May 2009

Baron

Hi,
has anyone some building details plans or pictures for the Pi four pro enclosure building process(or some common speakers technique)?
Regards,
Beto

Report message to a moderator

Enclosure Examples [message #29604 is a reply to message #29591]

Mon, 12 September 2005 13:45

GarMan
Messages: 960
Registered: May 2009

Illuminati (2nd Degree)

Hi Beto,

Here are a few examples from simpliest to more complex:

PI One
http://pg.photos.yahoo.com/ph/lowgc/album?.dir=c310&.src=ph&store=&prodid=&.done=http%3a//pg.photos.yahoo.com/ph/lowgc/my_photos

PI Three
http://pg.photos.yahoo.com/ph/lowgc/album?.dir=c95b&.src=ph&store=&prodid=&.done=http%3a//pg.photos.yahoo.com/ph/lowgc/my_photos

JBL Cabinet
http://pg.photos.yahoo.com/ph/lowgc/album?.dir=c1b7&.src=ph&store=&prodid=&.done=http%3a//pg.photos.yahoo.com/ph/lowgc/my_photos

Garden Sub
http://pg.photos.yahoo.com/ph/lowgc/album?.dir=e3bc&.src=ph&store=&prodid=&.done=http%3a//pg.photos.yahoo.com/ph/lowgc/my_photos

The last one's an interesting build. An 1,150 cubic ft cabinet cleverly disguised as a shed. 3/4" panel braced every 16" with 2x4's, veneered with 1" thick bevelled pine siding. A peak-shaped top to minimize standing waves and isolated off the ground with six cinder blocks to reduce resonance. Roofing felt and asphalt shingles on top further dampens out vibrations. Porting is done through a ridge-top and soffit vents.

Gar.

Report message to a moderator

Re: Enclosure Examples [message #29611 is a reply to message #29604]

Tue, 13 September 2005 21:00

beto1
Messages: 36
Registered: May 2009

Baron

Hi Gar,
Thank you very much, you have made a wonderful job and actually help me a lot. The following was my doubts before I read your post.
The first thing, and the most important,(and was my fundamental doubt) that I can see is about the vertex union. You use wooden plugs & glue and is similar to my original idea, but I have never seen an speaker job. An alternative is with special bolts (the ones with a continius diameter; I don't know its name in english, with wooden plugs as a cover), but I think your way is the purist. I supose that you don't use nails or bolts.
The second thing is about bracing, since I will use plywood and PI4 are small, I don't need to use too much of them, just a pair above and below the woofer.I will use 3/4" or 7/8" ("marine" was here the name for the one who has a treatment against moisture )
The third is about how to insert the woofer in the front panel, in other words, the diminution in the front panel thickness to fit the external ring not in the same front plane.
Thank you again.
Regards,
Beto

Report message to a moderator

Previous Topic:	Here's a dead-easy finish for Bourgeois woods you'll love
Next Topic:	Solid State vs Vacuum Tube Finish

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Nov 24 10:17:34 CST 2024