AudioRoundTable.com: Craftsmen » Table saw recommendations?

Home » Audio » Craftsmen » Table saw recommendations?

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

Re: follow-up [message #29003 is a reply to message #29002]

Wed, 31 March 2004 06:33

Dean Kukral
Messages: 177
Registered: May 2009

Master

I see what you are saying.

If the tracks are not parallel to the blade, then the fence is also not parallel to the blade. Since I spent $300 for a fancy fence for my Sears saw, I HAD to go check and see if it was parallel or not!

I was pleased to see that mine is parallel to the blade. :)

I don't think that my blade is moveable, but it has been a long time since I set it all up, so I may have forgotten. It is belt-driven.

I suppose that if this is an issue on an individual saw, then the directions for that saw will discuss it.

Report message to a moderator

[Message index]

		Table saw recommendations? By: crazychile on Mon, 29 March 2004 06:47
		Re: Table saw recommendations? By: Dean Kukral on Mon, 29 March 2004 07:34
		follow-up By: Dean Kukral on Mon, 29 March 2004 07:50
		Re: follow-up By: crazychile on Tue, 30 March 2004 06:19
		Re: follow-up By: Bill Fitzmaurice on Tue, 30 March 2004 06:56
		Re: follow-up By: Dean Kukral on Tue, 30 March 2004 18:50
		Re: follow-up By: Bill Fitzmaurice on Wed, 31 March 2004 06:11
		Re: follow-up By: Dean Kukral on Wed, 31 March 2004 06:33
		Re: follow-up By: Bill Fitzmaurice on Wed, 31 March 2004 08:38
		Re: More so with MDF By: BillEpstein on Wed, 31 March 2004 17:00
		Wait a minute By: Dean Kukral on Wed, 31 March 2004 06:49
		Re: Wait a minute By: Bill Martinelli on Fri, 02 April 2004 21:35
		Re: follow-up By: crazychile on Wed, 31 March 2004 09:40
		Re: follow-up By: Bill Fitzmaurice on Wed, 31 March 2004 09:56
		Re: follow-up By: crazychile on Fri, 02 April 2004 06:17
		Re: Table saw recommendations? By: Ryder on Mon, 29 March 2004 07:36
		Re: Table saw recommendations? By: elektratig on Mon, 29 March 2004 16:15
		Re: Table saw recommendations? By: wunhuanglo on Mon, 29 March 2004 16:45
		Re: All this is good stuff and.......... By: BillEpstein on Tue, 30 March 2004 20:32
		Re: BT3100 By: wunhuanglo on Wed, 31 March 2004 05:06
		Need more capacity? Make a bigger jig. By: Bill Fitzmaurice on Wed, 31 March 2004 06:06
		Re: REply to bigger capacity and sucky Ryobi By: BillEpstein on Wed, 31 March 2004 16:49
		Re: sucky Ryobi - Sorry, I disagree By: wunhuanglo on Wed, 31 March 2004 18:01
		Re: More space than saw By: Bill Martinelli on Wed, 31 March 2004 22:10

Previous Topic:	Tube PreAmp - Done! (almost)
Next Topic:	For Beginners

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Thu Nov 28 13:35:45 CST 2024