AudioRoundTable.com: Silicon Valley

Home » Audio » Silicon Valley » chip amps

Show: Today's Messages :: Navigator :: Polls
E-mail to friend

chip amps [message #10140]

Thu, 05 February 2004 09:28

Ed Schilling
Messages: 47
Registered: May 2009

Baron

Guys, try the TDA 1514AU (Mine were Signetics). Stupid low distortion. Will run on +- 16-27 volts DC. +-24 is the best. 30-40 watts depending on supply voltage. Easy to build. Cheap, even using the "best" components. I used ultra high speed, soft recovery diodes in the power supply. A good thing. Speaker Builder published an article (by me!)on the ones I was building at the time. This was way back in 1991. I just sent my "best one" off to Pit Hinder. I was shocked when I looked at the date on the reprint of the article.....Hard to believe it has been that long....time flys.
Ed
OH yea, WHEN you short one they blow cool little holes in the case and LOTs of smoke comes out. They must have really packed the smoke in those things.

Report message to a moderator

Re: chip amps [message #10141 is a reply to message #10140]

Thu, 05 February 2004 11:18

Wayne Parham
Messages: 18783
Registered: January 2001

Illuminati (33rd Degree)

>> They must have really packed the smoke in those things.

That's an advantage the folks that still smoke have over the non-smokers. They can just blow the smoke back in when something bad happens and the smoke comes out.

TDA 1514A

Report message to a moderator

Application? [message #10142 is a reply to message #10140]

Mon, 09 February 2004 20:48

GarMan
Messages: 960
Registered: May 2009

Illuminati (2nd Degree)

Ed,

Would you recommend following the recommended application in the spec sheet, or are there better "proven" configurations?

Gar.

Report message to a moderator

Re: Application? [message #10143 is a reply to message #10142]

Mon, 16 February 2004 20:14

Ed Schilling
Messages: 47
Registered: May 2009

Baron

Gar,
The recommended app. works just fine. I ended up omitting the input cap and the bootstrap components. They sounded better to me that way. I ran them on +-24 volts in the end but they also sounded fine on +-16. Hope this helps.
Ed

Report message to a moderator

Tried a Powerwave yet? [message #10149 is a reply to message #10140]

Sat, 13 March 2004 19:56

mrgrits
Messages: 5
Registered: May 2009

Esquire

It seems to be impressing the hell out of me and others. It offers such tube warmth and palpability for such a low cost. The only problem is the low-level hum and artifacts which could be a big problem for high efficiency speakers. I use a pair of Klipsch Reference speakers and can hear the audible artifacts at 10 feet. (Normally, I use a Select.) Don't hear it long, though, as I pour program through it pretty quickly.

Report message to a moderator

Re: Tried a Powerwave yet? [message #10154 is a reply to message #10149]

Thu, 25 March 2004 20:34

Ed Schilling
Messages: 47
Registered: May 2009

Baron

mrgrits,
Ordered a Powerwave yesterday. Have you tried a different power supply? The other fellow that suggested I give it a listen did not mention anything about hum. He is testing it and my "favorite" speakers. He likes the combo so I had to get one! We shall see, and I will report.
Ed

Report message to a moderator

Previous Topic:	please help me
Next Topic:	Howdy!

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Thu Nov 14 15:29:20 CST 2024