| |
499 Search Results Found |
| 1 |
Forum: Pi Speakers «»
Posted on: Tue, 13 April 2010 20:20 «»
By: hot grits
Re: 3pi/ 4pi plans
thanks for the reply. Must get pretty annoying answering questions about modifying plans that you spent countless hours on, and give out for free. I do appreciate your patience.
I think I am going to definitely go with the 3PI with a couple of modificat...
|
| 2 |
Forum: General «»
Posted on: Wed, 31 March 2010 17:16 «»
By: noviygera
Electricity... power strips and ac improvements
Hello friends,
For long I wanted to address the issues of too few power outlets and improvement of AC quality. I currently use two $10 power strips. I do not have $2000 for APS purepower or other exotic devices, so maybe some one can help me start off w...
|
| 3 |
Forum: Pi Speakers «»
Posted on: Sun, 28 March 2010 23:27 «»
By: lunkie
Re: 8 pi plans
Wayne, how would the Alpha 10 work if it was installed in your mid range horn? The horn section itself in the 8pi looks the same? I would have to build a rear chamber for it? I'm not concerned with a crossover network as I use a low level active network.
|
| 4 |
Forum: Pi Speakers «»
Posted on: Fri, 05 February 2010 22:29 «»
By: Wayne Parham
Re: Thinking of using electronic crossover - what should I know?
I like that little Bench crossover. I did a version of it for my speakers and found it to be very tailorable.
6DJ8 Tube CrossoverActive crossovers are similar to passive crossovers in some respect. One that's most important is the phase matters as muc...
|
| 5 |
Forum: Pi Speakers «»
Posted on: Mon, 14 December 2009 12:06 «»
By: Angelo.Bonavera
Theater 6 speaker
Hi all and many thanks to Wayne for his advice and his help.
I've finally completed my Theater 6 speakers:
I've used the Eminence Delta 12LF for the woofer, the eminence Delta10 for the midrange and the PSD2002 for the tweeter.
Here the cros...
|
| 6 |
Forum: Speaker «»
Posted on: Mon, 23 November 2009 01:07 «»
By: goldyrathore
Single tweeter line aray vs Line array with multiple tweeters
Hi,
I am in the design phase of building a line array. Its an active 2 way active system (with separate subwoofer crossed at 120hz).
Line height 60". Mid drivers are 2" full rangers and tweeters are Dayton ND20FA.
I have two choces :-
...
|
| 7 |
Forum: Pi Speakers «»
Posted on: Mon, 02 November 2009 14:21 «»
By: Wayne Parham
Re: Multisubs
I personally use a Class A FET amplifier, the ProFet amp from Selectronic. This requires a low-pass filter in front of the ProFet amp, and I have played with several types from passive line level filters to various off-the shelf devices.
The one I ...
|
| 8 |
Forum: Speaker «»
Posted on: Sun, 01 November 2009 08:38 «»
By: jtwrace
Re: help spend my money on an array project
I agree. Just so you know I will be using an active crossover with the arrays bi-amped.
|
| 9 |
Forum: Speaker «»
Posted on: Thu, 29 October 2009 17:47 «»
By: jtwrace
help spend my money on an array project
I built a 3-way speaker using a Foutek 2.0 and Accuton C-79. I was so impressed when I just crossed the mid / tweeter to my subs that I started thinking about building an array of the same. This design would use 20 C-79 with 18 Founteks. With some talki...
|
| 10 |
Forum: Silicon Valley «»
Posted on: Tue, 20 October 2009 16:02 «»
By: Wayne Parham
Re: plans for single frequency electronic crossover?
That may very well do the trick. Being a digital device, it must have the ability at least internally, since a filter is implemented as an algorithm. Whether or not you have access to the programming language to tailor the filters is the question, I gu...
|
Posting Rules
Members
Search
Help
Register
Login
Get a T-Shirt!
