|
351 Search Results Found |
1 |
Forum: General «»
Posted on: Wed, 28 April 2004 21:08 «»
By: Mike.e
plate amp wiring
…i have a simple questionequipment350watt plate amp2x20watt mini system with no line ini used to wire my little 20w amp, like thismini system with main speakers on the speaker outs as usualand wire the 20w sub amp in parallel with the speaker outsThis is …
|
2 |
Forum: Thermionic Emissions «»
Posted on: Fri, 17 September 2004 17:25 «»
By: Thermionic
Re: Glossary
… between the power supply connection and the plate tap. This has proven to be the most effective point. The special tap connects to the tube's screen grid, and provides a constant ratio voltage feedback between it and the plate that linearizes the tube in…
|
3 |
Forum: Silicon Valley «»
Posted on: Thu, 09 June 2016 15:13 «»
By: johnnycamp5
Crown amp
… has a low pass crossover capability and gain control built in.
Might this work, or is it better to use plate amps?
Am I correct in thinking that uber quality amplififcation is not necessary for distant subs and/or flanking subs, vs. the front mains…
|
4 |
Forum: Craftsmen «»
Posted on: Mon, 26 March 2007 01:08 «»
By: blake
amp enclosure
…I have a question about recessing the top plate.I used a rabbet bit to cut out a shelf for the top plate to sit on. The problem is that at the corners I have to pull the bit off the wood and it leaves a curve rather than a square end. Should I just chisel…
|
5 |
Forum: Group Build «»
Posted on: Sat, 05 March 2005 17:54 «»
By: PakProtector
the Amp
…40% as well for future as yet undetermined application/experimentation.CCS for the cathode of the input stage would be very similar to the Guinevere plate loads. Additional CCS for Ec2 ref would be LND150N3 based and similar construction.regards,Douglas…
|
6 |
Forum: Pi Speakers «»
Posted on: Mon, 23 April 2007 20:55 «»
By: tmoore
sub amp
Would an inexpensive plate amp such at the Dayton unit from parts express be sufficent to drive the 3 pi subwoofer? Are there other inexpensive options?
|
7 |
Forum: Pi Speakers «»
Posted on: Sat, 20 May 2006 18:34 «»
By: Shane
Amp question!
Wayne, what size plate amp would you recommend as a minimum with the designs you sent?
|
8 |
Forum: Thermionic Emissions «»
Posted on: Mon, 19 September 2005 14:47 «»
By: PakProtector
amp exercises
…choke input PS, valve rectifier and top plate.It is an interesting exercise in economics, and worth it for purposes of entertainment for sure. To top it all off, depending on which Peerless output I decide to replicate, it can be entertaining on so many …
|
9 |
Forum: Radio «»
Posted on: Wed, 12 November 2003 09:13 «»
By: Neo
Omega 18 plate amp?
Thanks Wayne. You're my source for the Omega 18. I just need to recover from all my scratch Foreplay purchases. I was going to use one of those SS plate amps for the Omega... Any recommendations?Tom
|
10 |
Forum: Tower «»
Posted on: Fri, 08 July 2022 10:17 «»
By: Pano
Re: John Busch
… NOS
2 Virtue 6.5" woofer, thk. Front plate. Poly cone. NOS woofer NOS
4 Peerless 6.5" Woofer. PE 264-1088 830657. NOS woofer NOS
2 Vifa 6.5" P17W3-00. NOS woofer NOS
2 Vifa 5" woofer. P13WW-00…
|