AudioRoundTable.com - RDF feed
type: channel
description: Audio advice and discussions with audiophiles and professionals. Free discussion forums, open to all and frequented by industry experts. Ask questions and get advice on stereos, speakers, hi-end amplifiers, pre-amps, home theater, tube hi-fi, turntables, vinyl, tweaks, music, films, video, DVDs and more.
items: pushin' Eminence 1" to 1.2KHz - how well does it work?
items: MD2001 - Good down to 1Khz; PSD2002 - Slightly higher
items: Re: MD2001 - Good down to 1Khz; PSD2002 - Slightly higher
items: Cool rendered image!
items: Re: MD2001 - Good down to 1Khz; PSD2002 - Altec horns
items: Peavey horns
items: Re: Peavey horns - maybe mine are CH-3?
items: Nope. Yours are bigger.

pushin' Eminence 1" to 1.2KHz - how well does it work?
type: item
description: Hi Wayne and group - right now have a long-throw (9.5mm) Eminence built 4 ohm car woof in a 12" Karlson - - almost "reaches" a CD-8 Eminence driver on 811 - running ~ textbook 1.8Khz network its lacking some midrange "life" - believe part of the problem besides limited woofer HF extention is due to baffle tilt of Karlson which may demand a driver with rising on-axis response (btw - the little Karlson woofer kicks pretty well) anyhow - have any of you run your Eminence 1" drivers in 1.2Khz xover regions and if so how were sound and dynamics? - I've tried 1.2K 3rd order hipass and it seemed relatively unstrained - didn't try it at intense levels - am tempted to run 4th order passive hi-pass. Best wishes! Freddy
creator: freddyi
date: 2001-12-15T17:29:10-00:00

MD2001 - Good down to 1Khz; PSD2002 - Slightly higher
type: item
description: I think you'll be OK with 1.2kHz crossover point, certainly if over 2nd or 3rd order. The MD2001 is good to 1kHz, the PSD2002 a little higher. I cross mine over at 1.6kHz third-order but 1.2kHz is probably OK if the horn loads there and the slope is high enough.
creator: Wayne Parham
date: 2001-12-15T18:01:24-00:00

Re: MD2001 - Good down to 1Khz; PSD2002 - Slightly higher
type: item
description: I find it weird that Eminence only advertises the frequency response of the 2002 as down to 1.5 kHz, yet the power rating is at 1 kHz. I am in agreeance with Wayne, I think you could run it down to 1.2 without a problem, you'll lose some power handling, though.... If you can keep the volume down a bit it should be fine.
creator: Adam
date: 2001-12-15T18:56:32-00:00

Cool rendered image!
type: item
description: Very cool rendering? What did you use to do that? I've become pretty good with Imagine, Pv3D and Pov-Ray. I love that stuff!
creator: Wayne Parham
date: 2001-12-15T19:29:48-00:00

Re: MD2001 - Good down to 1Khz; PSD2002 - Altec horns
type: item
description: Hi Wayne and group! thanks for the reply (wow - great image by Adam!!) -looked at my old graphs of the Eminence CD-8 without network on Altec horns - 811 has a LF corner just ~ 500Hz and 511 somewhat below 400Hz ~1/2 octave so these old horns should provide some decent loading. btw - a PV CH-2 looked real smooth - not sure about the compensation needed - surprisingly, it measured very extended in HF - sounded kinda laid-back - is CH-2 considered CD? Very Best! Freddy
creator: freddyi
date: 2001-12-15T19:42:11-00:00

Peavey horns
type: item
description: I've used Peavey CH-3 horns for quite a while. At first, I was concerned about their two-piece design. But after testing and trying them out for a while, I realized there was no consequence. The seam is acoustically small and they measure and sound nice.
creator: Wayne Parham
date: 2001-12-15T20:08:23-00:00

Re: Peavey horns - maybe mine are CH-3?
type: item
description: Hi again Wayne! my Peavey have a 10" by 19" flange, are 2-piece with depth to throat (which has a round-square inital transition) is ~11.625" - are those CH3? take good care! Freddy
creator: freddyi
date: 2001-12-15T20:23:25-00:00

Nope. Yours are bigger.
type: item
description: The CH-3 has a 5" x 14" mouth.
creator: Wayne Parham
date: 2001-12-15T20:32:16-00:00