Search Engine

Search Results
Your search for 8Ω found the following documents (of 61488 documents searched):
Displaying documents 11-20 of 26, with best matches first:

11. ProSound Forum - Re: l-acoustics power ratings mtd115a - Wayne Parham, March 17, 2006 at...

Looks like great stuff. I have no experience with that particular brand, but I do have experience with sound systems in...
URL: http://audioroundtable.com/ProSound/messages/36.html

12. GuitarAmp Forum - Re: ??????Can any of you tech's help????? - Wayne Parham, August 28, 2008 at...

 Each speaker should probably have voice coil resistance of 5Ω or so. A speaker advertised as having 8Ω average impedance...
URL: http://audioroundtable.com/GuitarAmp/messages/755.html

13. GuitarAmp Forum - Re: amp to cabinet - Wayne Parham, October 01, 2008 at 13:13:16

 You can connect a jack to the speakers on your Fender Twin, and connect to your 4x10 cabinet from that. The load impedance...
URL: http://audioroundtable.com/GuitarAmp/messages/768.html

14. PiSpeakers Forum - Re: 2 Pi amp - Kramer 903? - Wayne Parham, April 29, 2009 at 13:05:41

 That amp should work fine with two π loudspeakers. If it produces 10 watts with a 4Ω load, then the output voltage is...
URL: http://audioroundtable.com/PiSpeakers/messages/23814.html

15. PiSpeakers Forum - Re: 4pi - Wayne Parham, August 26, 2008 at 18:30:39

 To use a 4Ω woofer, scale the caps and coils on the woofer circuit and also increase tweeter attenuation by changing the...
URL: http://audioroundtable.com/PiSpeakers/messages/22875.html

16. PiSpeakers Forum - Re: Now with measurements. - Wayne Parham, February 27, 2008 at 13:48:37

 Good stuff, Ken. The peaking you're seeing is what we want, but there is a little bit too much of it. If you load a...
URL: http://audioroundtable.com/PiSpeakers/messages/22162.html

17. PiSpeakers Forum - Re: Cabinets for Four Pi speakers - Wayne Parham, April 10, 2009 at 20:22:19

 What you propose is fine. Just make sure the Helmholtz frequency is 38Hz and put the tweeter horn immediately above the...
URL: http://audioroundtable.com/PiSpeakers/messages/23748.html

18. GuitarAmp Forum - Re: ohms selector to mono input - Wayne Parham, June 07, 2005 at 15:38:54

Match the speaker to the amp. Set the amp according to the impedance of the speaker. You can parallel two speakers to cut...
URL: http://audioroundtable.com/GuitarAmp/messages/188.html

19. GuitarAmp Forum - Re: Speaker upgrade - Wayne Parham, April 13, 2009 at 14:47:03

 Usually amps are pretty tolerant of load impedance - up to a point. Tube amps sometimes don't like high impedance loads and...
URL: http://audioroundtable.com/GuitarAmp/messages/803.html

20. VintageAudio Forum - Re: HELP....What ohm are these Utah speakers? - Wayne Parham, January 08,...

 Measure the voice coil resistance. Advertised impedance will be about 25% higher. If the voice coil measures 6Ω or so, it's...
URL: http://audioroundtable.com/VintageAudio/messages/668.html

Documents 11-20 of 26 displayed.

Results Pages: << Previous | 1 | 2 | 3 | Next >>

Search Tips - Main Page