Home » Audio » Thermionic Emissions » schematic
schematic [message #10931] Fri, 04 February 2005 17:33 Go to next message
Manualblock is currently offline  Manualblock
Messages: 4973
Registered: May 2009
Illuminati (13th Degree)
There was an article in AudioeXpress describing a nice 211 SE design with Mercury rec tubes. I have been following the build up of that design and it appears it has reaped quite a reputation. Nothing like the big bore triodes. Anyone have experience with these tubes?

Report message to a moderator

Re: schematic [message #10932 is a reply to message #10931] Sat, 05 February 2005 08:20 Go to previous messageGo to next message
Wayne Parham is currently offline  Wayne Parham
Messages: 18675
Registered: January 2001
Illuminati (33rd Degree)
Maybe that one would be good for a group build?

Report message to a moderator

Re: schematic [message #10933 is a reply to message #10932] Sun, 06 February 2005 09:32 Go to previous messageGo to next message
Manualblock is currently offline  Manualblock
Messages: 4973
Registered: May 2009
Illuminati (13th Degree)
It Certainly would make me happy!
However it require's very high plate voltages; difficult to wind transformers and expensive tubes and passive parts. Might not fly with the regular crowd. Unless you are interested???

Report message to a moderator

Re: schematic [message #10934 is a reply to message #10933] Sun, 06 February 2005 09:50 Go to previous messageGo to next message
Wayne Parham is currently offline  Wayne Parham
Messages: 18675
Registered: January 2001
Illuminati (33rd Degree)

How expensive? I mean, we didn't slouch on the power supply transformer for Guinevere, and it wasn't too bad. How much do you think we are talking about for the parts for this mercury rectified SE 2A3?

Report message to a moderator

Re: schematic [message #10935 is a reply to message #10934] Sun, 06 February 2005 12:49 Go to previous messageGo to next message
Manualblock is currently offline  Manualblock
Messages: 4973
Registered: May 2009
Illuminati (13th Degree)
Well I would assume the 2a3 trans would be fairly inexpensive but for a 211 with 1100v on the plate might get pricey. The guys who built this went for about 800$ for the handwound power and opt's. Then 866 merc tubes and 211's as well as oil caps etc. the total came in at around 1k.
Then you like real nice chassis so add 150$ to that.

Report message to a moderator

Re: schematic [message #10936 is a reply to message #10935] Sun, 06 February 2005 13:44 Go to previous messageGo to next message
Wayne Parham is currently offline  Wayne Parham
Messages: 18675
Registered: January 2001
Illuminati (33rd Degree)

Gotcha. So about twice the cost of Paramours, yes? I wonder what Heyboer might charge for these transformers. If we're lucky, maybe they already have what we need in their inventory. You think there's any chance of that?

Report message to a moderator

OPTs [message #10937 is a reply to message #10936] Sun, 06 February 2005 15:16 Go to previous messageGo to next message
Damir is currently offline  Damir
Messages: 1005
Registered: May 2009
Illuminati (2nd Degree)

For 845/211/GM70, etc. project, you can consider the new "Lundahl" LL1688 OPT. From "K&K Audio", price is $275, not too bad.
And for 2A3 & 300B projects, 1664 serie (with 50mA,60mA,80mA,100mA DC current) is nice. They are 3k:8 Ohms only, price is $125.
The only drawback with "Lundahl" OPTs is that they are "naked and ugly" - for under-chasis montage, or buy some separate cover?
I have 1664/80mA OPTs, some experiments are on their way...

Report message to a moderator

Re: OPTs [message #10938 is a reply to message #10937] Sun, 06 February 2005 15:30 Go to previous messageGo to next message
Wayne Parham is currently offline  Wayne Parham
Messages: 18675
Registered: January 2001
Illuminati (33rd Degree)

Not bad at all. What do you think about a PS transformer?

Report message to a moderator

Re: OPTs [message #10939 is a reply to message #10938] Mon, 07 February 2005 05:39 Go to previous messageGo to next message
Damir is currently offline  Damir
Messages: 1005
Registered: May 2009
Illuminati (2nd Degree)
Huh, I used just Plitron/Amplimo toroids (excellent, but high price) and local custom - made toroids (cheap, but not that good). No experience with other brands, but for the 2A3 project, I`ll work it out somehow (Hammond?)...

Report message to a moderator

Re: OPTs [message #10940 is a reply to message #10939] Mon, 07 February 2005 07:15 Go to previous messageGo to previous message
Manualblock is currently offline  Manualblock
Messages: 4973
Registered: May 2009
Illuminati (13th Degree)
Superbowl; good game for a change. I can try and post a link to the schematic for the 211 triode amp, it sounds nice with those Lundhal Iron and less expensive than any handwound. I f I could put the 211 amp together that is my dream amp, 20watts of SE triode power.

Report message to a moderator

Previous Topic: PSUD/switchercad
Next Topic: Really cool DIY Rogue's Gallery I fell over
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ] [ PDF ]

Current Time: Fri Apr 19 01:46:58 CDT 2024

Sponsoring Organizations

DIY Audio Projects
DIY Audio Projects
OddWatt Audio
OddWatt Audio
Pi Speakers
Pi Speakers
Prosound Shootout
Prosound Shootout
Smith & Larson Audio
Smith & Larson Audio
Tubes For Amps
TubesForAmps.com

Lone Star Audiofest